hiltinter.blogg.se

#Big bathtub overflow plate install#
#Big bathtub overflow plate upgrade#
#Big bathtub overflow plate free#

#Big bathtub overflow plate install#

If you are removing an overflow plate with a pop-up or plunger style stopper attached, you should have a bucket handy to drop the old parts into without dirtying your tub.Ģ) Install the black retainer nut behind the adapter bar with a flathead screwdriver. Remove any screws holding your existing overflow plate and carefully remove. Follow these simple steps with all materials included, the only tool you should need is a flathead screwdriver.ġ) Remove your existing overflow plate.

#Big bathtub overflow plate free#

Watch our easy installation videos and call our toll free number with any questions on repairing your tub drain and replacing a bathtub overflow plate. We offer exceptional customer service with the simplest method of upgrading your bathtub.īathtub Overflow Plate Easy Installation InstructionsĮasily install your new bathtub overflow plate in three simple steps for a shiny new overflow plate in less than 5 minutes.

#Big bathtub overflow plate upgrade#

Watco Innovator® Snap-On bathtub overflow plate provides a complete, clean look to your new tub drain with a matching finish and easy installation. It’s never been easier to transform the look of your tub with the SimpliQuick® Tub Fix and Innovator® Snap-On Overflow Plate Trim Kit by Watco. Easily convert 1-hole, 2-hole or trip lever tub overflow plates with a beautiful, new overflow plate in under 5 minutes.į wants to help you repair, replace or upgrade your tub to your complete satisfaction. Use your existing bolt if you have a 1-hole, 2-hole overflow plate. Images on this site may not reflect this updated change.įYI - bolt not included to secure retainer nut behind the H bar adapter. FYI - As of 2019, "WATCO" imprinted on Chrome, Nickel, Bronze, White, Chrome Brushed, Polished Nickel and Wrought Iron finishes. The Innovator kit includes the Innovator overflow plate, black retainer nut and an H bar adapter. The Watco Innovator® overflow bathtub plate kit easily retrofits a 1-hole, 2-hole and trip lever overflow plates. Replace the drain assembly and then fasten the plate with the two mounting screws to finish the job.The BRAND NEW Watco SimpliQuick® Tub Fix "white finish" composite bathtub stopper (Made from same corrosion-resistant Innovator overflow plate material) is a perfect addition to purchase with the Watco Innovator® snap-on overflow kit.

Make sure it seats evenly for a complete seal around the connection. The overflow pipe will have a little play (although not much) that should allow you to adjust its position and make room for the gasket. Use a little plumber’s silicone grease to lubricate the gasket and work it into place around the mouth of the overflow body. When installing the gasket, make sure the thick side is at the bottom.

You’ll need to buy a new overflow washer or gasket from the hardware store. But since I had already opened the wall, here’s a look at the rear of the overflow body where the old gasket is falling out. With any luck you can complete the repair from the tub without having to open the wall. I used an old wire hanger to dig out the rotted gasket material from the overflow body. Shown here is the old deteriorated gasket that must be removed. Pull out the assembly, including the drain plug. The first step is to remove the screws that mount the cover plate. The good news is that replacing an overflow drain gasket is a fairly easy fix. I only mention this to demonstrate that plumbing leaks can happen in some seemingly unlikely places, and locating the problem can be half the battle. Something about the manner in which my wife showers-whether it’s the way she shampoos her hair or maybe shaves her legs-directs water onto the overflow drain, and consequently past the deteriorated gasket. Finally, as she was showering, I inspected the plumbing from the floor below and followed the active leak all the way up to the overflow drain. The tub only leaked when my wife took a shower in it. Nor did we have problems when my kids took a bath. Most frustrating of all: I could not reproduce the leak when I took a shower. I eventually opened up the ceiling and the wall behind the faucet to investigate. Convinced of this, I replaced a couple of faucet valves, tightened some threaded connections, and sealed a couple different drain connections with silicone tape, yet I still had a leak. It didn’t make sense to me that the overflow drain got enough water exposure to be the source of a leak which was ruining a drywall ceiling downstairs.

You wouldn’t think a bathtub overflow drain would be the source of a water leak, especially if you never fill the tub to a level at which water would enter the opening. Alternative Heating & Fireplace InsertsĪ simple leaky gasket can cause a big problem.